مقطورة نصف منخفضة

MÜLLER-MITTELTAL 3-Achs Satteltieflader überfahrbar m. Radmulden

* TS 3 RM 30.0:
* Wabco EBS-E (electronic braking system)
* RDÜ tire pressure monitoring system
* Emergency release device for spring-loaded cylinders
* Drum brakes
* 3 x 11-ton BPW axles
* Air suspension with lifting and lowering system and RtR valve
* Last axle as self-steering axle with electro-pneumatic steering lock
* Side impact protection
* Landing gear at the front and swivel supports at the rear of the chassis
* 15-pin power connector
* LED taillights
* Mechanical Adjustable warning sign packages at the front and rear
* Rotating beacon (removable) at the rear left
* Straight sheet steel fenders
* Spare wheel holder in front of the bulkhead cross member (without spare wheel)
* Trailer platform with 45° beveled front corners and a toolbox at the front made of galvanized, powder-coated sheet steel (W = 2,480 x H = 500 x L = 665 mm) with a hinged lid
* 400 mm aluminum side walls (RAL 9010) on the sides of the trailer platform, foldable and removable
* Rear wall -150 mm- high
* Rear slope on the trailer platform to the low bed, approx. 700 mm long, each with one recessed lashing ring
* Trailer platform with 50 mm clamped wooden planks and low-loading platform with 60 mm clamped wooden planks
* Teardrop plate above the axles
* 9 mechanical folding extensions to 3 m Total width, but not including the rear slope (extension planks present with closed storage compartment perpendicular to the direction of travel under the loading area)
* 2 lashing bars embedded in the outer frame of the semi-trailer platform on each side, 3 lashing rings on each side in the low-loader platform, and an additional 1 lashing ring in the center of the rear end beam, 2 x 5 ton lashing rings screwed to the bottom of the outer frame of the wheel wells on each side,
* 2 x 6.4 ton lashing rings on each side. UVV lashing rings in the excavator boom rest
* Excavator boom rest from the end of the last rigid axle over the steering axle to the end support, continuous with internal reinforcement profile approx. L = 2,450 x W = 770 mm x D = 270 mm
* Two wheel recesses on each side, 390 mm deep and 640 mm wide, with retractable covers for transporting wheel loaders with a wheelbase of 3,120 - 3,620 mm, front recess at the bottom, slanted upwards by 1,100 mm to a length of 2,050 mm, rear recess at the bottom, slanted upwards by 580 mm to a length of 1,550 mm
Hfjdpfx Ael Tiiyjdyor
* Hydraulic. Folding ramp with extendable tip, approx. 4,650 x 720 mm, including load-holding valves and hydraulic lateral ramp adjustment.
* The outer board on the ramp is made of 50 mm hardwood.
* Loading area above the turntable: approx. 3,950 x 2,480 mm.
* Loading height (unloaded): approx. 1,470 mm.
* Lower loading area: approx. 8,500 x 2,520 mm.
* Loading height (unloaded): approx. 910 mm (including 860 mm approach slope).
* Chassis, folding supports at the rear, loading ramps, mechanical. Hot-dip galvanized folding extensions
* -- Axles, springs, and air chambers painted in a single black tone --
* Suitable for 2- and 3-axle tractors
* Fifth wheel height: approx. 1,220 mm
* Tires 235/75R17.5
* Gross vehicle weight of 48,000 kg technically possible
* Vehicle is hot-dip galvanized
* Side walls painted in RAL 9010 pure white
* Side walls painted in a RAL color available for an additional charge
* New vehicle with manufacturer's warranty
* Errors and prior sale subject to change
* Available for immediate delivery from Egestorf

تمت ترجمة الإعلان تلقائياً، وقد تكون هنالك بعض الأخطاء في الترجمة.