مقطورة نصف مفتوحة

Fliegl SDS 390 Plateau mit Teleskopierung für Baustahlmattentransport

Custom-Made Transport Solution
Ppedpfx Anoi Ri Sze Hsw
Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer requirements.

Chassis, Saddle, and Haulage Company
Fine-grained steel welded construction in lightweight design, saddle plate with interchangeable 2 kingpins, main frame reinforcement for 25 tons, with center of gravity at 3 m load length in the retracted state.
13 pairs of hooks for securing lashing straps, welded onto the crossbeams
23 pairs of lashing eyes recessed into the outer frame, each 3.5 tons
Outer frame with Load-Lock profile for attaching lashing straps
Note! Not usable with sideboards!
24 tons, 2-speed support winch in reinforced design for loaded coupling/uncoupling, single-sided operation
Chocks with holder
Aluminum side impact protection
Under-run protection
Half-shell fenders
with anti-splash flaps according to EC
1 spare wheel holder for 1 tire, with wheel fastening kit
1 closed storage box for stakes, open at the top, below the loading area, doors on both sides, w=450 mm/h=400/420 mm/d=2460 mm
6 pairs of pull-out stake pockets, for rectangular section stakes 80x80 mm, extendable from loading width of 2000 mm to 3100 mm
4 pairs of stake pockets recessed into the outer frame, for rectangular section stakes 80x80 mm
11 stake pockets recessed in the center of the floor, for rectangular section stakes 80x80 mm, with reinforcement beam, installed between the outer stake pockets
5 x 3 pairs of stake pockets recessed into the outer longitudinal beams, for rectangular section stakes 80x80 mm, including reinforcement beams - for load securing to the front and rear during the transport of reinforcing steel mats, 2x5000 mm or 2x 6000 mm
6 lightweight plug-in stakes, w=80/d=80/, usable height approx. 1850 mm, hot-dip galvanized, with rope guide at the top for strap tensioning
12 lightweight plug-in stakes, w=80/d=80/, usable height approx. 1850 mm, hot-dip galvanized, with lashing eyes welded to the bottom on both sides
Note: Stake pockets/plug-in stakes are not designed for the sole securing of long materials, pipes, etc. without strapping.
2 plastic toolboxes, with drawer and insert, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included)
6 steel winches with wire rope and clevis hook, with rope guide through the outer frame, 1 removable gearhead for steel winch - supplied loose
Telescoping
Main frame telescoping
extendable by a maximum of 4,000 mm and lockable every approx. 500 mm
Locking with pneumatic pin locking + indicator for frame locking on both sides, operated via hand knob, operation for brake/locking and suspension on the control panel on the left side in front of the axles
Storage compartment between the longitudinal beams in the extended state
Axles + Suspension
SAF disc brake axles with 430 mm disc diameter
Last axle with trailing arm, with automatic reversing lock via reversing light, and additional locking function on the vehicle via hand knob, as well as manually via switch in the towing vehicle (Pin 10), without truck installation.
Axle track offset mm
Air suspension
1st axle automatic lift axle, additionally electrically operable from the truck, with starting aid
Braking System
2-line compressed air braking system
Colored line routing for easy servicing
Spring brake parking brake
2 fail-safe coupling heads at the front
EBS manufacturer according to the manufacturer's choice, electronic braking system with EBS

تمت ترجمة الإعلان تلقائيًا. قد تحدث أخطاء في الترجمة.