حفارة صغيرة

KUBOTA Kompaktbagger KX037-4 MS03 3.+4. Steuerkreis

SN: 209

Kubota Compact Excavator KX037-4 with MS03 Quick Coupler
3rd & 4th Control Circuits AUX1/AUX2, Proportional Control
Factory-installed load hook on MS03 Quick Coupler
Dipper arm length: 1,525 mm

Accessories:
1x digging bucket,
Width: 400 mm,
Attachment: MS03 Symlock,
Bucket transport hook,
Full cutting edge

Kubota Crawler Excavator KX037-4 MS03:

Operating weight: approx. 3,695 kg,
3rd & 4th Control Circuits AUX1/AUX2, proportionally controlled,
Load holding valve on lift cylinder,
Load holding valve on dipper cylinder,
Factory-installed load hook on MS03 quick coupler,
Selector valve for depressurized return line for hydraulic hammer,
Battery master switch,
Dipper arm 1,525 mm,
3-cylinder Kubota engine,
Rubber tracks,
Dozer blade,
Radio preinstallation,
Sliding front window,
Mechanical suspension seat,
Dumping height: approx. 3,545 mm,
Digging depth: approx. 3,410 mm,
2x halogen work lights on top of cab,
1x halogen work light on boom

Standard Equipment:

Engine/Fuel System:
Original KUBOTA engine,
Dual air filter element,
Acoustic refueling system,
Battery disconnect switch,
Water separator with drain tap,
Automatic idle control

Undercarriage:
Short-pitch rubber track 300 mm,
2 travel speeds (high/low),
Automatic load-dependent travel speed changeover,
4 externally guided lower rollers per track frame,
1 upper carrier roller

Hydraulic System:
2 variable axial piston pumps and 1 gear pump,
Emergency lowering via hydraulic accumulator,
Hydraulic test ports,
Straight travel function,
Auxiliary circuits routed to end of dipper arm,
Auxiliary circuit (AUX1) with max. adjustable hydraulic oil flow,
Auxiliary circuit AUX1 proportional via right control lever / AUX2 proportional via left control lever (standard for Germany & Austria),
Direct tank return line for AUX1

Safety System:
Engine safety start device in the left control console,
Hydraulic lockout system,
Swing brake for upperstructure,
Travel motors with brake system,
Original Kubota anti-theft system,
Safety/pipe rupture valves for dipper arm and boom (ISO8643)

Working Equipment:
1,525 mm long dipper arm,
One work light on boom

Cabin:
ROPS (Roll-Over Protective Structure, ISO 3471),
OPG (Operator Protective Guard, Top Guard Level I, ISO 10262),
Cab heating with front window de-icing and air dehumidification,
Fully suspended operator seat with weight adjustment (fabric seat),
Retractable seat belt,
2 work lights on cab,
Radio installation kit in cab (2 speakers, radio antenna, radio mounting compartment),
Pilot-operated hydraulic controls with wrist supports,
Display unit with diagnostics,
Front window opening system with gas strut support,
Mounting points for front window guard,
Switch and wiring harness for beacon light,
12V power supply,
Emergency hammer for emergency exit

Technical Data – Dimensions with Cabin:
Overall width: approx. 1,550 mm
Overall height (cab): approx. 2,470 mm
Overall length: approx. 4,900 mm
Ground clearance: approx. 285 mm
Dozer blade width x height: approx. 1,550 x 340 mm
Track width: approx. 300 mm
Minimum front swing radius without boom offset: approx. 2,100 mm
Minimum front swing radius with boom offset to the left: approx. 1,730 mm
Boom swing angle (left/right): 69 / 49°

Technical Data – with Cabin:
Operating weight with cab: approx. 3,695 kg
Working weight with cab: approx. 3,770 kg
Gbedpfxex Tli Do Agrsg
Bucket c... (continues)

تمت ترجمة الإعلان تلقائياً، وقد تكون هنالك بعض الأخطاء في الترجمة.