مقطورة نصفية مفتوحة مع قماش مشمع

Fliegl SDS 350 Gardine Standard

The images are archive images; the vehicle may still be in use.
Fine-grained steel welded construction, kingpin plate with interchangeable 2" kingpin, slightly angled outer frame with "Load-Lock profile" for securing lashing straps, 24 tons. Two-stage support wind, single-sided operation, with straight lower section, without lateral thrust compensation. Note: Free support base angle or free rear swivel radius approx. 1930 mm without supports, extension ladder at the rear, door lock on the side, pallet box for 32 Euro pallets (long version), ground clearance approx. 300 mm. Rear impact protection, "blocker" - transverse galvanized steel angle, as forklift protection and to protect the door hinges, pallet stop on both sides approx. 15-20 mm high, in bolted version, loading height reduced by approx. 15-20 mm.
Axles + Suspension
SAF disc brake axles with 430 mm disc diameter, "axle/chassis laser-aligned" to reduce tire wear and fuel consumption, air suspension, without lift axle.
Braking system: 2-line compressed air braking system, color-coded line routing for easy servicing. Spring brake parking brake.
2 fail-safe coupling heads at the front, without connecting line, EBS manufacturer Haldex, electronic braking system with EBS socket at the front, without connecting cable, with raise and lower valve.
Vehicle - driving stability system, brake pad wear indicator via EBS-CAN bus signal, for display on the instrument panel in the cab; truck must be appropriately prepared, axle load detection via EBS-CAN bus signal, for display on the instrument panel in the cab; truck must be appropriately prepared, no truck installation (no calibrated scale).
Tire pressure monitoring system TPMS Haldex, via EBS, without truck installation (this requires a prerequisite in the truck).
Electrical system: 24 volts, multi-chamber lights in LED with resistor, yellow LED lighting on the side, license plate lighting in LED.
2 white position lights at the front, 2 white/red side marker lights at the rear, 1 x 15-pole socket at the front, without connecting cable, additional LED work lights at the rear, switched via reversing light.
Floor: Sieve printing plates approx. 30 mm thick, on longitudinal supports for high point load capacity for forklift axle load up to max. 7100 kg.
Kdedpfxoy Tvwxo Apiol
Body
Assembled body, assembled body.
Front wall / front corner posts
2,580 mm high, corner posts made of steel in full volume design, release mechanism for side tarpaulin on the front wall, "crash blocker", at the bottom inside at approx. 140 mm height with steel impact protection.
Intermediate posts: 2 pairs of sliding posts, adjustable over the entire length, with 4-fold insertion pockets and a long pocket at the bottom. 2 pairs of post positions.
Insertion slats: 5 rows of aluminum V-insertion slats.
Rear wall / rear corner posts
Rear corner posts made of steel to the lower edge of the roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet.
Rear portal doors, 2-leaf with 2 internal twist-lock latches each.
Tarpaulin: Tarpaulin, with welded-in horizontal and vertical straps, tension closures made of stainless steel.
Roof: Sliding roof, end lift at the rear that can be folded up, with the roof that can be slid from back to front, L-roof beam for the automotive industry, internal width between the roof beams approx. 2,490 mm, tarpaulin color: white, roof non-elastic, hardly any deflection of the roof beam when loading and unloading, anti-ice system, with 1 hose in the mid

تمت ترجمة الإعلان تلقائيًا. قد تحدث أخطاء في الترجمة.