مقطورة نصف منخفضة

SCHWARZMÜLLER RH240 Jumbo Plateau Tieflader ausziehbar > NEU <

Schwarzmüller RH240

Jumbo Flatbed Low Loader Semi-Trailer

Extendable telescopic design – for building material and construction machinery transport

- NEW - UNUSED -

Gross vehicle weight rating: 36,000 kg
Curb weight: 10,340 kg

Internal length approx. 13,570 mm =
Front platform length approx. 3,950 mm
Rear platform length approx. 9,620 mm

Platform width (lower deck) approx. 2,540 mm

Loading height in well (unladen) approx. 830 mm


Frame:
Extendable central-frame welded construction

Extension length 6,000 mm

Pneumatically lockable, operation on the trailer + additional position for 40ft container in the well

Reinforced design for building material transport, rated for 20 t over 5 m at center of gravity and for construction equipment transport up to 20 t

Frame is suitable for the transport of timber components L/W/H approx. 13,000/575/3,200 mm

Reinforced frame for spot loads front and rear at support blocks

Reinforced outer frame in the cranked platform 6 mm

Reinforced outer frame in the well 6 mm

Tapered cross members

Sliding intermediate support approx. 300 mm (not removable), mechanically lockable, as stake pocket cross member for 80x80 mm box stakes, as well as 1 pair of 5 t lashing rings on the outside integrated into the intermediate support

Frame for 2-axle tractor units, coupling height unladen approx. 960 mm – 1,020 mm with air-suspended tractor

3 pairs front and 10 pairs rear, 10 t lashing rings, extendable at both sides on the outer frame, can also be folded outwards for oversize securing

10 pairs of lashing mushrooms with welded-in round steel on the underside of the outer frame


Frame Attachments:
10 pairs of stake pockets with reinforcement for 80x80 mm box stakes, both sides on the outer frame
6 stake pocket cross members for 80x80 mm box stakes
24 steel box section stakes, 80x80x5 mm, effective height approx. 2,000 mm, with lashing holes at top for straps, hot-dip galvanized
3 pairs of container locks in the well platform, retractable, for
1 x 20ft container
1 x 30ft container
1 x 40ft container (when extended)

U-profile rail for drive-on ramps at end of frame


Landing Gear:
Mechanical steel landing gears, 2 x 12 t
2 drop-down supports, both sides at rear of frame


Gjdpfju A Nilsx Adtskd
Wheels:
Tyres 205/65 R 17.5
Steel rims 6.00 x 17.5


Axles:
SAF low loader axles with drum brakes
Axle lift on 1st axle
Axle spacing 1,310 + 1,410 mm
Self-steering SAF trailing axle, approx. 20° steering angle, electro-pneumatic reverse lock automatically activated in reverse
Last axle is trailing steering axle


Brakes/Suspension:
Brake system by Wabco
Brake/air connectors with 2 individual coupling heads yellow/red, EBS/ABS socket at front
Air suspension with raise/lower function, total lift approx. 200 mm
Automatic leveling to programmed ride height above 15 km/h


Assistance/Safety Systems:
Standard reporting interval
Every 15 minutes with ignition on
Every 24 hours with ignition off
Axle load indicator via EBS canbus signal for display in driver's cab (truck must be equipped accordingly)
SmartBoard by Wabco for reading data via display (kilometres, axle aggregate load, brake diagnostics, etc.)


Floor:
35 mm larch floorboards, impregnated on both sides, fitted longitudinally with small gaps, above the wheels with steel chequer plate covers


Front Wall:
Fixed profiled steel front wall, approx. 2,700 mm high with 2 central supports
2 front corner posts, integrated into the front wall, bolted on face side
2 lashing points each on the up

تمت ترجمة الإعلان تلقائياً، وقد تكون هنالك بعض الأخطاء في الترجمة.