مقطورة منخفضة التحميل

MÜLLER-MITTELTAL 5 achs Tieflader, Nachlauflenkachse, MA liftbar

T5 Profile 50.0:

----Brakes:

* Wabco EBS (electronic braking system)
* Emergency release device for spring brake cylinders
* Drum brakes

----Axles:

* 5 x 11 t Gigant axles
* 3rd axle liftable (when axle is lifted, ride height +30 mm)
* Last axle is self-steering (locking of the self-steering axle for maneuvering can be done from the cab without truck-side installation, as well as via a switch on the trailer); the lock must be disengaged before driving on public roads
* Forced lifting and lowering of the lift axle for maneuvering purposes (truck-side installation required) with speed-dependent control via EBS electronics

----Suspension:

Nodpfx Asl Tihueb Ejku
* Air suspension, raise/lower system with RtR valve

----Drawbar:

* 1,500 mm long drawbar with 50 mm towing eye and manual height adjustment

----Electrics / Lighting:

* Smartboard as an information tool with pressure sensors for indicating total axle load per axle group
* Tire pressure monitoring with display option in the truck via EBS signal (no installation required on the truck)
* LED lighting system 12/24 V
* Removable LED beacon at the rear

----General Attachments:

* Mechanical warning board kit for 3 m total width
* Toolbox made of galvanized sheet steel approx. 650 x 300 x 600 mm, left side
* Front fenders made of plastic and rear fender skirts made of galvanized sheet steel

----Lowbed Platform:

* Prefabrication of the turntable platform with 45° corners and 3 storage compartments with lockable folding covers (covers open to the rear)
* Shortening of the lowbed platform by 500 mm to 6,280 mm including extended stepped offset by 500 mm forward
* Rubber matting on the fold-down frame, approach slope, and running surface of the lowbed platform
* Bamboo wood inserted between the longitudinal beams before the excavator stick storage

----Load Securing (Load Securing Package):

* 2 x 6.4 t lashing rings at the front corners
* At the front and rear side corners, 2 x 13.4 t UVV lashing rings each
* Additionally, 5 x 10 t UVV lashing rings per side (swiveling and lowerable, loadable in all directions)
* 4 stake pockets per side, each with a simultaneous 2 t lashing option
* 1 x 16 t UVV lashing ring on the rear crossmember

----Widening:

* Extendable and folding widening outriggers for 3 m total width (plank holders under the chassis on the right side)

----Excavator Stick Rest:

* Continuous excavator stick rest with reinforced profile from final axle to rear end cross member approx. L=2,350 x W=770 x H=270 mm, 2 pairs of 6.4 t UVV lashing rings on the sides of the stick rest

----Ramps:

* Hydraulic foldable ramp with dual-line hydraulics and deployable tip section approx. 4,650 x 720 mm including load holding valves and hydraulic side shift

----Rear Support:

* Hydraulic rear support

----Hydraulics:

* Hydraulic flow divider (for hydraulic pump output in the truck of over 40 l/min up to max. 140 l/min)

----Loading Height:

* Loaded: 890 mm +/- 20 mm via air suspension

----Loading Area Dimensions:

* Loading area above turntable: 2,600 + 390 x 2,520 mm
* Lowbed loading area: 6,280 + 500 x 2,520 mm including 860 mm approach slope

----Painting:

* Chassis, turntable, drawbar, widening consoles, and drive-on ramps hot-dip galvanized
* Tow bar, axles, hydraulic axle supports, and air tanks painted in black

----Information:

* New vehicle with manufacturer's warranty
* Subject to errors and prior sale

----Delivery Time:

Available from calendar week...

تمت ترجمة الإعلان تلقائياً، وقد تكون هنالك بعض الأخطاء في الترجمة.